Posted by montytx on March 6, 2009 at 10:49 pm
I just returned from my first ski trip in a dozen years. My how things have changed. The mountain was wired with 3g service everywhere. I managed to take pics and post them on facebook while being stuck in a gondola for 10 minutes. Now that is cool.
Skis have also changed. I was informed that my old size of 210 or so was now more like 170. Apparently the skis are fatter at the edges so they can be shorter. I rented normal two days and expert one. I noticed quite a difference with the expert skis, they were a lot faster. I am debating whether or not to by my own skis. At $30 a day it seems like a good investment and would only take a few years to pay for itself if I ski every year. But there is a hick up. American Airlines wants $15 each way for each bag. That is a full day of rentals and means it would take a couple of years longer just to break even. So unless I stumble across a deal I can’t pass up I doubt I’ll bother. It is just easier to rent, and I’m no expert.
Snow Basin was spectacular. I have been to several resorts in Colorado and even Park City and SB was incredible. Since the Olympics was held there, they completely upgraded everything including new lodges at the base and the top of the mountain. The runs were very well groomed and it was only a little icy. If you go over to the runs on the left side the they are in even better shape since the traffic is lower. Driving there from my sister’s in Ogden was a treat
everyday going between the mountains and by the dam. I highly recommend this resort if you are in Utah.
Continue Reading
Posted by montytx on February 8, 2009 at 3:33 am
As I continue to overhaul this car and get it road worthy I decided to tackle the struts this week. The front struts require jacking the car up and removing both wheels. You then have 3 bolts in the engine area that have to be removed to drop the struts down. At the bottom of the struts you must undo to small screws that hold the brake line and some other line to the struts. Then there are 2 large 22mm bolts that attach to the brake and steering assembly that must be undone. Then the struts will come down and out.
This is when the work starts. I suggest you go to the auto store and buy or borrow some strut spring compressor tools. These compress the spring down so you can safely remove it from the old strut. There are a few other items to consider. The strut top mount may be bad. Mine didn’t look bad, but I replaced them anyway. They cost around $70 each at the auto store. I got them on ebay for $60/set. Under this is a ball bearing pack that comes apart with a little effort. But be very careful, there are about 20 large ball bearings in there that can fly ou and go everywhere. I suggest opening it in a bucket and cleaning it with some engine cleaner. Once that is done you will want to repack them with fresh grease. This took me about 15 minutes a side. Then then is a large plate that sits on top of the spring to keep it in place. Under this is a rubber gasket that my be worn down.
You will need to compress the spring to be able to remove the top screw that holds the strut assembly together. I ended up using an electric drill to turn a socket head to tighten the strut tool which is nothing more than a large screw with 2 hook like plates sticking out of it that fasten onto the spring and compress it.
One the compression is done you simply unscrew the top screw and take apart the unit. Then you get the new strut and reassemble the same why it came apart. Make sure you use the left strut and the right strut on the correct side. My brand was universal for the front so it was not an issue. You also need to make sure you re align the strut head to tilt inwards. Total time to remove and reassemble these was around 4 hours. Total cost was around $350 for parts. My understanding is that shops charge around a grand to do the work I did. Not a bad savings.
These pre assembled full struts are a great option at Amazon and should cut down on time:
Front Left
Front Right
Strut Top Hat (you will need 2)
Continue Reading
Posted by montytx on January 21, 2009 at 3:24 am
Its been a long, exciting day of dramatic change and optimism. Growing up in the South, as a Texan, I never ever dreamed that something so dramatic could happen in my lifetime. A Black man has become POTUS. But, beyond the color of his skin he is, quite simply, the best man for the job. I listened to Obama’s speech today and was duly impressed with his keen sense of understanding of where our nation is and what we need to do. More enticing to me is that Obama is one of my people. He came from a middle class family and was raised by his single mother and grandmother. I can completely relate to his experiences. He went to Harvard on his own merits, and appears to be a great orator capable of reaching across party lines to make things happen. Only time will tell, but I believe in my heart that he is the agent of change this country needs. We need to face some very harsh realities and start living our lives according to those realities.
I can only hope he is as successful as his inauguration was today. The sense of pride and joy I felt that our country could put aside its differences and prejudices to elect Obama within a generation of MLK truly shows how much this country can do in such a short time. Compared to the Middle East, China or a 100 other countries where change is measured in centuries, rather than decades, this is truly a remarkable time in history. God bless our country.
Continue Reading
Posted by montytx on January 21, 2009 at 1:00 am
Since I have free time right now I decided to do some vehicle maintenance on my 95 Lexus ES300. I bought this car this Summer from my brother and have really enjoyed it. It gets great gas mileage and I installed a pioneer avic700BT with nav. But the car has some aging issues, the power steering started going out as soon as I got it, the starter is on the fritz and all 4 struts are worn out.
So I decided to tackle the power steering today and thought I would make note of a few tips to help other lost souls who run into this design nightmare, courtesy of Toyota. The first thing you notice about the power steering in these cars ( and Camrys) is that the power steering pump is located under the Engine near the firewall on the passenger side. So removing it from above is impossible which leaves underneath. The framing under the car is quite extensive, which is good for safety but bad for maintenance. Log story short you have to remove the passenger front tire as well as the well skirting inside to gain access to the power steering. This is where the nightmare begins.
One would think that once the skirting is removed there would be plenty of room to remove the pump. One would be wrong. Once you remove everything you have a space about the size of a large coffee can to work with. In this space is the pump which is barely visible since it sits up about 4″ out of your view. The first thing to do is loosen the lower 12mm bolt and remove the belt. This loosens up the pump so it can be moved around. There are then 2 low pressure supply hoses that come from the resevior that are clamped on. These need to unclamped and moved up out of the way after they have drained. There is also an electrical sensor that has to be unplugged. The challenge then begins. The pump has 2 exiting pressurized lines laving the pump and they are located on the top of the pump and almost impossible to get at. The large one is 22mm and you will need a short extension and a long exentsion to get at it from above. My short ext has a flexible socket head on it which allowed the socket to angle in towards the bolt. Not to difficult if you don’t have to make 2 trips to the auto store just to get a 22mm socket. The last remaining pressurized line is a 17mm nut that can only be loosened from the bottom with an open faced wrench. And no ordinary wrench will do, you will need a short wrench to fit in the space to loosen this bolt up. This was trip #3 to the auto store for me. The real challenge though is getting the wrench in place in this small space and getting enough force to loosen the hose. It only took me 1/2 hour to get it done.
Once this is off, the unit dropped right down and came right out. Total time for me to go through all of this mess was about 4 hours. Reinstalling it only took 1 hour. Learning curve, priceless.
There is a 12mm bolt on the bottom and one on the top holding the pump in place.
You can get the pump on Amazon here.
Continue Reading
Posted by montytx on January 3, 2009 at 11:14 pm
Maybe I am missing something but I don’t understand why Hamas would provoke Israel into a full scale invasion. Are they dumb enough to think someone is going to come to there aid? That most definitely is not going to happen when the US has close to 200K troops in 2 nearby countries. I don’t think Iran even has the cojones to try that.
They had a workable truce up until a few months ago and then deliberately opted to start launching homemade, tin can rockets into Israel. That is like jumping into the cage with the lion and poking him in the eye repeatedly, then expecting someone to come to your rescue.
I do understand their plight. They want their own homeland with no interference from Israel, but do they think this is the way to go about it? It just defies all logic.
Continue Reading
Posted by montytx on January 2, 2009 at 11:13 pm
My son is quite creative and decided over the holidays to create a flash movie. I was quite impressed with the motion he created between the bus and the city. Even keeping the sun in the background. Very impressive for a 12 year old.
Black Hole Sun Movie
Continue Reading
Posted by montytx on January 2, 2009 at 11:00 pm
I own and maintain another site about green contruction. I started this site becuase I am in construction and have noticed just how difficult it is to get good information about green contstruction products and techniques. You really have to look around and then some to find good information about products that are considered green. More interesting is the misconceptions that exist out there about what is and isn’t green. Anyway Please visit my other site if you are interested in those topics. I try to blog on that site often as I find things that are pertinent to that industry.
Continue Reading
Posted by montytx on December 13, 2008 at 12:58 am
I thought that it was very interesting that Estonia is going to allow voting via mobile phone in 2011. Apparently users will plug some sort of chip into their phone, verify their identity and then be able to vote. I have to wonder just how secure this is going to be. The head of security for this states
The system and software have proven effective and reliable in an independent security audit, Kaidro said. He dismissed security concerns, claiming the system “is the most secure way to authenticate digital signatures.”
Of course, what this doesn’t address is voter fraud. How exactly does this prevent people from selling their votes, or in this case, their chips? Yet, I have to wonder if something like this could be implemented here in the United States? It would definitely make voting easier and likely increase participation. Imagine being able to turn on your phone and vote in a few minutes from anywhere. The possibilities are endless, I can imagine myself on a remote beach and voting for my state Rep.
I have to question why the US has not tested a set up like this. It is interesting that we are so interested in preventing voter fraud but are more than willing to elect Governors and other politicians that flaunt the law and think they can get away with it. It seems to me they would be the ones most likely to try to manipulate votes, and yet they are in office already. Which begs to question, ” how much worse can a mobile phone voting system be?”
Continue Reading
Posted by montytx on December 9, 2008 at 5:18 pm
I was stunned to see the 33% drop in Real Estate sales in the DFW market place today. Home prices are down a whopping 15% from their highs. I think we Texans’ were naive enough to think we were not going to see the worst of this economy in our state. Oil and Gas seemed to give us a nice buffer for a while, but my have the mighty fallen. I can get gas for under a buck fifty. Who would have thunk it? I don’t think we have seen the bottom of the oil barrel either. It looks like it is having trouble holding on to $50 a barrel.
Of course the cause of this whole mess is spending more than we make. Everyone seems to have decided to spend 1.25 for every $1.00 they made and the result is a lot of worthless noncollectable debt and many over priced houses that should never have been built for people spending too much. The bottom line is the housing market and a lot of other goods to have to depreciate to a point where the average American can afford them again. So 15% seems like a lot but I am going to guess the number is closer to 20-25% in the drop of home values in DFW. Of course that varies greatly by neighborhood. I wouldn’t expect anything inside the loop to drop more than 5-10%.
Continue Reading
Posted by montytx on December 6, 2008 at 6:11 pm
I recently stumbled across a type of photography called tilt shift photography. This is normally achieved with an expensive specialized lense designed just for this type of photography. I am not an expert at photography, nor do I aspire to be, but I am accomplished at Photoshop and I can manipulate just about any image out there to my liking. I decided to give the tilt shift effect a run and was pretty happy with the results. All of these are not technically tilt shift. I took some liberties and messed around with the images.
Essentially what is involved in varying degrees is applying a mask with a gradient where I want the focus to be. Then I applied a gaussian blur between 10-15 pixels depending on the effect I was going for. That creates the focal point.In some instances I just applied a mask and then erased anything I wanted to be blurred. On the image of the log cabin I created a copied layer and then blurred the bottom image while the top was erased til I was happy with the result.
Next I went to the brightness/ contrast and bumped them up 20-30% til I liked the colors. Lastly I opened up curves and adjust the low end down and the high end up.
The result is an ethereal looking image that in many cases looks like a picture of a model.
Continue Reading